To allow us to react more flexibly and above all faster to the requirements in the factory, initially a prototype, then later, in the expansion phase 1, an independent test procedure system was developed that enables a skilled executive on site to develop rework programs for the plant.
In the past this has been done by expanding the diagnostic programs developed for use in after-sales service. JOIN US!!!INPA User documentation V 2.2ġ IntroductionWith the introduction of new control units or control unit versions in production a diagnostic program for this control unit, for example for post processing, must be provided. INPAInterpreter for test proceduresUser documentationĪuthors: Georg Luderbck Michael Koch Roland Stadtmller Run D-CAN.EXE and setup CAN BUS mode.LED should OFFĭon't use USB Extender cable, directly connect interface to computer.- JOIN US!!!SOFTING GmbH Richard-Reitzner-Allee 6 85540 Haar Tel.: 089/45656-0 Fax: 089/45656-499 Configuration-For configuration interface:
Modes of configurator fileD-CAN.exe, that is on the CD-disk given in thefolder_D_CAN_USBas follows: Your Adaptor is already configurated to work with BMW both K-line and CAN-bus. Close the soft and disconnect the Adaptor from USB-port each time you change the Choose the model of BMW and type of modul you want to see Rune the soft INPA with file:\EC-APPS\INPA\BIN\inpaload.exe Plug the Adaptor into OBD-II connector of BMW- Turn the Ignition into ON position
Check the parameter if you useġ1) In the fileC:\Windows\OBD.INIput the number of USB-COM-port to the value that youġ2) Run from CD-disk a file Driver_D_CAN_USB\OBDSetup.exeġ5) Use the following order of using adaptor: (That is default parameter after installing from CD-disk given. Value ofLatency Timerfrom16 to1.Remember the number of the COM-port choosen !ġ0) In the file EDIABAS.INI"Interface = STD:OBD"must be choosen
The file inpa.ini that is in the root directory of CD-disk given.ħ) Plug the Adapter into spare USB-port and install drivers manually from theįolderDriver_D_CAN_USB using Driver Wizardof yourWindows XP-Service Pack-2ĩ) InAdvancedfield change number of COM-port to the value from2to 4. Activate all spare boxes with:INPA 5.0.1 - UPDATE,NCS Expert 3.0.8 - UPDATEĦ) Find the file :\EC-APPS\INPA\CFGDAT\ named inpa.ini and replace it with Choose configuration BMW Group Rectification programs UK, pressContinue.Ĥ. While choosing the HDD disk for initial setup do not change letter C:\. ChooseENGLISH, pressContinue, then press Continue againĢ. Activate all spare boxes with :EDIABAS 6.4.3 - UPDATE,INPA 5.0.1 - UPDATE,ġ. Choose configuration BMW Group Rectification programs UK, press Continue.4. Yourinstallation must be on drive:\ONLY !ģ. ChooseENGLISH, pressContinue, then press Continue again2. Copy folderEC-APPSonto disk:\ģ)Run file Step_1\NFS\Entpackt\disk1\SETUP.EXEWhile installing choose User ModeFurther choose in opening windows:ġ.Parametrieren einer neuen Konfiguration ohne Daten2.OBDĤ)Run fileStep_2\INSTALL\Instprog.exe1. Installation INPA EDIABAS FULL-English-Editionġ)Delete ALLversions ofINPA-ADSfrom your computer or remane all INPA-ADS folders.For example: remaneINPAinto _INPA, EDIABASinto _EDIABAS and so on.Ģ)Open folderStep_1\in the root of CD-disk given.